Відео

What is the overall height of the cart when assembled?

Why is that cable so long that you have to crank it for three weeks?

Nice plan but its to complicated and takes to long to setup. Other versions are simpler and less equipment is needed. also the expense is Less. It was a nice video

Why would they design a pulley where you have to remove the wheels/spring clips to screw it down? When I see simple, stupid decisions like this, it steers me away to a different product, say one with 1/2" more flange to screw the pulley down so you dont have to remove the pulley wheels. It really makes you wonder where else they skipped spending the extra 10 minutes to design something correctly.

At the end of video if you did everything outside will the top of the hoist go in a standard 7 foot high garage door?

cannot hear you

What is the size of the screw that connect to the strap on the crank. Mine was missing.

That's a nice product, but man, that's a whole lot of work just to get the top off. I use the Roll N Jack and it's much easier, plus I don't have to lower it to the ground and I just park the Jeep right under it.

This is such a masterfully done instructional video!! Simple and just enough extras! 💯

Would it be able to just hold the top instead of putting down in storage position?

This was great just got mine gonna watch this again when I use it for sure

Video does not follow manual received with the Hoist-A-Top for 4 door JK. In the manual I can see the offset of 1/2 inch between the holding points. There is no word in the video about the offset. In the manual you ask to measure 32 inches on the roof. Despite the fact the drawing in manual shows that the roof is 32 inches (which is not) there is no explanation from which side (rear ort front of the Jeep) to measure the 32 inches. I am lost.

I looked this item up on line to check the price and noticed it states it won't fit my 1991 Jeep YJ hardtop. I can't see any reason why not? Please fill me in. Thanks

I can’t find the JK hooks anywhere

Is there a version of this hoist that holds all 4 doors?

How do I lower the horizontal bar after use?

Great video - thank you. I sure wish Lange would have powder coated rather than paint. It’s a bit disheartening watching the paint flecks fly while assembling.

For the price, it's cheaper to build a proper hoist into the ceiling

Great video. Thank you.

All these over price hoist systems are not only overpriced but way more complicated than it has to be. I bought an $85 2,500lbs wench from Harbor Freight, a 2x12 board at 8ft long, drilled some holes for the wrench and nut/bolted the wench to the 2x12 and then tossed it all above my ceiling joists and nailed the 2x12 above the joists once I got it where I needed it. I lowered the hook with the wireless remote it came with, and got a 100ft nylon rope for the straps. Since I have a Gladiator I went under the front of the hard top with one rope and then another separate rope inside the back window and through the front of the hard top and tied figure-8 knots on both sides of each of the two ropes once I got the size I needed and then cut the excess off. And that was it. I have a powered hoist that lifts my 85lbs top off that HAS a weight maximum of 2,500lbs and everything is bolted and nailed down. Took me all of 30 minutes to slap together and I guarantee you it’s stronger than this $450 rig in the video and it costs no more than $100 all together.

just ordered, thank you for this video!!!👏

Where's the other 2 doors go for a 4 door?

What is the total weight this hoist can lift? I have a Rugged Ridge rack attached to my hard top that weighs approximately 100 lbs.

just got it in the mail yesterday !! the box was destroyed hahaha but everything inside was perfect !!! instruction was spot on and it went together without any issues !!! great cart thanks for the video and great jeep tool !!! i will enjoy it for a loooooooong time

Can y’all just not read a tape measure ? Where are to measuring the bolts from ?

Great video! How much time am I gonna need to build this thing?

Need this, great video

excellent video

Ugggg! Good grief this is way over engineered.

This is totally unsafe way to lift a heavy load.

I finally got my hoist-a-cart. I love it!

Is the 2x6 alone enough to support the weight of the hoist with the 4” lag bolts? Assuming that there were no studs in the ceiling where the motor is installed.

Why is it impossible to find one of these???

Or you can just keep it simple and buy a Top Loft Pros

Really impressed - that is an elegant solution, especially if you don't like to leave your top suspended above your jeep when parked in the garage. Out of curiosity, is it ok to leave the top in that seated vertical configuration for extended periods of time? Like for many months? Or will it stress and potentially warp/crack it?

As a woman, I was nervous about putting this together and using it myself and I have to say, I appreciated the detail in both the assembly of the gen 2 hoist a cart and this one! I love it. I’m very happy with the purchase and can remove the top alone and replace it alone.

Does a LJ top work with this? LJ tops are 200lbs approx.

TOPSY HOOKS ARE BETTER ! GOOGLE TOPSY HOOKS

I think my hoist device is only a single spool device. Does this change anything?

great video, can the roof stay hung up in the device as storage, so I can park My Jeep with the bonne underneath it in the garage?

Loved the video. Im about to check it out. I have a 4 dr

Can you use this to take the doors off? (before you take the top off of course)

How tall is it when you lower the arm assembly down all the way like you did at 18:30?

What is the Z depth for a 2 door JK top layed down verticle (From back wall of the garage to the furthest point out). Trying to figure out the amount of depth from the wall of the garage I need. Thank you!

Looks pretty straight forward. I wonder how easy is it to disassemble/reassemble? I need something like this when I go on vacation to the beach and flat tow it behind our RV. (I know I could just get a soft top lol but I would rather not deal with the hassle of swapping from one to the other every year)

I don’t have a cement floor. How will this work on grass and uneven ground?

What happens if your ceiling joists are running the opposite way of the wall you are installing the hoist on?

Cannot keep tension on front strap even doing everything according to the video. Just keeps releasing even after cranking it. Did I miss something?

This is the best JT top hoist design I've found so far. I haven't tried any of them yet. Still researching.

This video was outstanding.. I had to watch a few times before I even started. but easily explained and demonstrated.. it did take me a few hours . but good step by step explainations